View AD851507_4139069.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier AD8515
FEATURES
Single-supply operation: 1.8 V to 5 V Offset voltage: 6 mV maximum Space-saving SOT-23 and SC70 packages Slew rate: 2.7 V/s Bandwidth: 5 MHz Rail-to-rail input and output swing Low input bias current: 2 pA typical Low supply current @ 1.8 V: 450 A maximum
PIN CONFIGURATION
OUT 1 V- 2
5
V+
AD8515
03024-001
TOP VIEW +IN 3 (Not to Scale) 4 -IN
Figure 1. 5-Lead SC70 and 5-Lead SOT-23 (KS and RJ Suffixes)
APPLICATIONS
Portable communications Portable phones Sensor interfaces Laser scanners PCMCIA cards Battery-powered devices New generation phones Personal digital assistants
GENERAL DESCRIPTION
The AD8515 is a rail-to-rail amplifier that can operate from a single-supply voltage as low as 1.8 V. The AD8515 single amplifier, available in 5-lead SOT-23 and 5-lead SC70 packages, is small enough to be placed next to sensors, reducing external noise pickup. The AD8515 is a rail-to-rail input and output amplifier with a gain bandwidth of 5 MHz and typical offset voltage of 1 mV from a 1.8 V supply. The low supply current makes these parts ideal for battery-powered applications. The 2.7 V/s slew rate makes the AD8515 a good match for driving ASIC inputs such as voice codecs. The AD8515 is specified over the extended industrial temperature range of -40C to +125C.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2002-2007 Analog Devices, Inc. All rights reserved.
AD8515 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications....................................................................................... 1 Pin Configuration............................................................................. 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Electrical Characteristics............................................................. 3 Absolute Maximum Ratings............................................................ 6 Thermal Resistance ...................................................................... 6 ESD Caution.................................................................................. 6 Typical Performance Characteristics ..............................................7 Theory of Operation ...................................................................... 12 Power Consumption vs. Bandwidth ........................................ 12 Driving Capacitive Loads .............................................................. 13 Full Power Bandwidth ............................................................... 13 A Micropower Reference Voltage Generator.............................. 14 A 100 kHz Single-Supply Second-Order Band-Pass Filter ... 14 Wien Bridge Oscillator .............................................................. 15 Outline Dimensions ....................................................................... 16 Ordering Guide .......................................................................... 16
REVISION HISTORY
7/07--Rev. C to Rev. D Updated Format..................................................................Universal Updated Package Designator Throughout.................................... 1 Changes to Table 1, Supply Current/Amplifier ............................ 3 Changes to Table 2, Supply Current/Amplifier ............................ 4 Changes to Table 3, Large Signal Voltage Gain, Power Supply Rejection Ratio, and Supply Current/Amplifier........................... 5 Changes to Figure 10........................................................................ 8 Changes to Figure 35...................................................................... 14 Updated Outline Dimensions ....................................................... 16 Changes to Ordering Guide .......................................................... 16 3/05--Rev. B to Rev. C Changes to Specifications ................................................................ 2 Changes to Ordering Guide ............................................................ 5 4/03--Rev. A to Rev. B Change to Figure 5 ......................................................................... 12 2/03--Rev. 0 to Rev. A Added new SC70 Package .................................................Universal Changes to Features ..........................................................................1 Changes to General Description .....................................................1 Changes to Pin Configuration .........................................................1 Changes to Specifications.................................................................2 Changes to Absolute Maximum Ratings........................................5 Changes to Ordering Guide .............................................................5 Changes to TPC 3..............................................................................6 Changes to TPC 10............................................................................7 Changes to TPC 13............................................................................8 Changes to TPC 27......................................................................... 10 Changes to TPC 28......................................................................... 10 Added new TPC 29 ........................................................................ 10 Changes to Functional Description ............................................. 11 Updated to Outline Dimensions .................................................. 14 8/02--Revision. 0: Initial Version
Rev. D | Page 2 of 16
AD8515 SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VS = 1.8 V, VCM = VS/2, TA = 25C, unless otherwise noted. Table 1.
Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol VOS IB Conditions VCM = VS/2 -40C < TA < +125C VS = 1.8 V -40C < TA < +85C -40C < TA < +125C -40C < TA < +125C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low Short Circuit Limit POWER SUPPLY Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product NOISE PERFORMANCE Voltage Noise Density Current Noise Density CMRR AVO VOS/T VOH VOL ISC ISY VOUT = VS/2 -40C < TA < +125C RL = 10 k 0 V VCM 1.8 V -40C < TA < +125C RL = 100 k, 0.3 V VOUT 1.5 V 0 50 47 110 Min Typ 1 2 Max 6 8 30 600 8 10 500 1.8 Unit mV mV pA pA nA pA pA V dB dB V/mV V/C V V mV mV mA A A V/s MHz nV/Hz nV/Hz pA/Hz
Input Offset Current
IOS
1
400 4
IL = 100 A, -40C < TA < +125C IL = 750 A, -40C < TA < +125C IL = 100 A, -40C < TA < +125C IL = 750 A, -40C < TA < +125C
1.79 1.77 10 30 20 325 450 500
SR GBP en in
2.7 5 22 20 0.05
f = 1 kHz f = 10 kHz f = 1 kHz
Rev. D | Page 3 of 16
AD8515
VS = 3.0 V, VCM = VS/2, TA = 25C, unless otherwise noted. Table 2.
Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol VOS IB Conditions VCM = VS/2 -40C < TA < +125C VS = 3.0 V -40C < TA < +85C -40C < TA < +125C -40C < TA < +125C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product NOISE PERFORMANCE Voltage Noise Density Current Noise Density CMRR AVO VOS/T VOH VOL 0 V VCM 3.0 V -40C < TA < +125C RL = 100 k, 0.3 V VOUT 2.7 V 0 54 50 250 Min Typ 1 2 Max 6 8 30 600 8 10 500 3 Unit mV mV pA pA nA pA pA V dB dB V/mV V/C V V mV mV dB dB A A V/s MHz nV/Hz nV/Hz pA/Hz
Input Offset Current
IOS
1
1000 4
IL = 100 A, -40C < TA < +125C IL = 750 A, -40C < TA < +125C IL = 100 A, -40C < TA < +125C IL = 750 A, -40C < TA < +125C VS = 1.8 V to 5.0 V -40C < TA < +125C VOUT = VS/2 -40C < TA < +125C RL = 10 k
2.99 2.98 10 20 65 57 85 80 350
PSRR ISY
450 500
SR GBP en in
2.7 5 22 20 0.05
f = 1 kHz f = 10 kHz f = 1 kHz
Rev. D | Page 4 of 16
AD8515
VS = 5.0 V, VCM = VS/2, TA = 25C, unless otherwise noted. Table 3.
Parameter INPUT CHARACTERISTICS Offset Voltage Input Bias Current Symbol VOS IB Conditions VCM = VS/2 -40C < TA < +125C VS = 5.0 V -40C < TA < +85C -40C < TA < +125C -40C < TA < +125C Input Voltage Range Common-Mode Rejection Ratio Large Signal Voltage Gain Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High Output Voltage Low POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product NOISE PERFORMANCE Voltage Noise Density Current Noise Density CMRR AVO VOS/T VOH VOL 0 V VCM 5.0 V -40C < TA < +125C RL = 100 k, 0.3 V VOUT 4.7 V 0 60 54 450 4.99 4.98 10 20 65 57 85 80 410 75 2000 4 Min Typ 1 5 Max 6 8 30 600 8 10 500 5.0 Unit mV mV pA pA nA pA pA V dB dB V/mV V/C V V mV mV dB dB A A V/s MHz nV/Hz nV/Hz pA/Hz
Input Offset Current
IOS
1
IL = 100 A, -40C < TA < +125C IL = 750 A, -40C < TA < +125C IL = 100 A, -40C < TA < +125C IL = 750 A, -40C < TA < +125C VS = 1.8 V to 5.0 V -40C < TA < +125C VOUT = VS/2 -40C < TA < +125C RL = 10 k
PSRR ISY
550 600
SR GBP en in
2.7 5 22 20 0.05
f = 1 kHz f = 10 kHz f = 1 kHz
Rev. D | Page 5 of 16
AD8515 ABSOLUTE MAXIMUM RATINGS
TA = 25C, unless otherwise noted. Table 4.
Parameter Supply Voltage Input Voltage Differential Input Voltage Output Short-Circuit Duration to GND Storage Temperature Range KS and RJ Packages Operating Temperature Range AD8515 Junction Temperature Range KS and RJ Packages Lead Temperature (Soldering, 60 sec) Rating 6V GND to VS 6 V or VS Observe derating curves -65C to +150C -40C to +125C -65C to +150C 300C
THERMAL RESISTANCE
JA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 5. Thermal Resistance
Package Type 5-Lead SOT-23 (RJ) 5-Lead SC70 (KS) JA 230 376 JC 146 126 Unit C/W C/W
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Rev. D | Page 6 of 16
AD8515 TYPICAL PERFORMANCE CHARACTERISTICS
450 VS = 2.5V 400
SUPPLY CURRENT (A) SUPPLY VOLTAGE (V)
5 6
4
350
3
300
2
250
03024-002
1
03024-005
200 4.65
4.70
4.75
4.80
4.85
4.90
4.95
0 4.65
4.70
4.75
4.80
4.85
4.90
4.95
BANDWIDTH (MHz)
BANDWIDTH (MHz)
Figure 2. Supply Current vs. Bandwidth
450 400 160
Figure 5. Supply Voltage vs. Bandwidth
VS = 2.5V 140 VOL VOH 100 80 60 40
03024-006
300 250 200 150 100
03024-003
OUTPUT VOLTAGE (mV)
350
SUPPLY CURRENT (A)
120
50 0 0 1 2 3 4 5 6
20 0
0
5
10 LOAD CURRENT (mA)
15
20
SUPPLY VOLTAGE (V)
Figure 3. Supply Current vs. Supply Voltage
500 VS = 5V 120 100 80 450 60 40 20 0 -20 350 -40
03024-004
Figure 6. Output Voltage to Supply Rail vs. Load Current
270 VS = 2.5V AMPLITUDE = 20mV 225 180 GAIN
GAIN (dB)
ISY (A)
PHASE
90 45 0 -45 -90 -135
400
-60 -80 1k 10k 100k 1M 10M
300 -50
-25
0
25
50
75
100
125
150
-180 50M
TEMPERATURE (C)
FREQUENCY (Hz)
Figure 4. ISY vs. Temperature
Figure 7. Gain and Phase vs. Frequency
Rev. D | Page 7 of 16
03024-007
PHASE (DEGREES)
135
AD8515
120 100 80 60
PSRR (dB) ACL (dB)
96 VS = 2.5V 92 VS = 2.5V
40 20 0 -20 -40
G = 100 G = 10 G=1
88
84
80
03024-008 03024-011
-60 -80 10k 100k 1M FREQUENCY (Hz) 10M
30M
76 -50
0
50 TEMPERATURE (C)
100
150
Figure 8. ACL vs. Frequency
120 100 80 60
CMRR (dB) NUMBER OF AMPLIFIERS
Figure 11. PSRR vs. Temperature
430 VS = 2.5V 344
VS = 2.5V AMPLITUDE = 50mV
40 20 0 -20 -40
03024-009
258
172
86
03024-012
-60 -80 10k 100k 1M FREQUENCY (Hz) 10M
100M
0 -6.24
-4.27
-2.29
-0.32
1.66
3.63
VOS (mV)
Figure 9. CMRR vs. Frequency
140 120 100 80 60 40 20
03024-010
Figure 12. VOS Distribution
150
VS = 2.5V AMPLITUDE = 50mV
VS = 2.5V
OUTPUT IMPEDANCE ()
+PSRR
100
PSRR (dB)
-PSRR
50
-20 100
1k
10k
100k
1M
0 1k
10k
100k FREQUENCY (Hz)
1M
10M
FREQUENCY (Hz)
Figure 10. PSRR vs. Frequency
Figure 13. Output Impedance vs. Frequency
Rev. D | Page 8 of 16
03024-013
0
GAIN = 100
GAIN = 10
GAIN = 1
AD8515
25 24 23 -ISC
VOLTAGE (2V/DIV)
VS = 5V
VS = 2.5V VIN = 6.4V
22
ISC (mA)
VIN VOUT
21 20 19 18 17 16 15 -50 0 50 TEMPERATURE (C) 100
03024-014
+ISC
150 TIME (200s/DIV)
Figure 14. ISC vs. Temperature
Figure 17. No Phase Reversal
VS = 2.5V
VS = 2.5V CL = 50pF VIN = 200mV
VOLTAGE (100mV/DIV)
VOLTAGE (13V/DIV)
03024-015
0
250
500
750
1k
1.25k 1.5k 1.75k
2k
2.25k 2.5k TIME (1s/DIV)
FREQUENCY (Hz)
Figure 15. Voltage Noise Density
Figure 18. Small Signal Transient Response
VS = 2.5V GAIN = 100
VS = 2.5V CL = 500pF VIN = 200mV
VOLTAGE (100mV/DIV)
VOLTAGE (200mV/DIV)
03024-016
TIME (1s/DIV)
TIME (1s/DIV)
Figure 16. Input Voltage Noise
Figure 19. Small Signal Transient Response
Rev. D | Page 9 of 16
03024-019
03024-018
03024-017
AD8515
VS = 2.5V CL = 300pF VIN = 4V 120 100 80
VOLTAGE (1V/DIV)
VS = 1.5V AMPLITUDE = 50mV
60
CMRR (dB)
03024-020
40 20 0 -20 -40 -60 -80 10k 100k 1M FREQUENCY (Hz) 10M
03024-023
100M
TIME (1s/DIV)
Figure 20. Large Signal Transient Response
Figure 23. CMRR vs. Frequency
100mV
VIN
VS = 1.5V GAIN = -40 VIN = 100mV
VS = 0.9V CL = 50pF VIN = 200mV
VOLTAGE
0V 0V
2V VOUT
03024-021
VOLTAGE (100mV/DIV)
TIME (2s/DIV)
TIME (1s/DIV)
Figure 21. Saturation Recovery
Figure 24. Small Signal Transient Response
0V
VS = 1.5V GAIN = -40 VIN = 100mV
120
VIN
270 VS = 0.9V AMPLITUDE = 20mV 225 180
PHASE (DEGREES)
03024-025
100 80 60
135 90 45 0 -45 -90 -135 100k 1M FREQUENCY (Hz) 10M -180 30M
VOLTAGE
-100mV 2V VOUT 0V
GAIN (dB)
40 20 0 -20 -40
03024-022
-60 -80 10k
TIME (2s/DIV)
Figure 22. Saturation Recovery
Figure 25. Gain and Phase vs. Frequency
Rev. D | Page 10 of 16
03024-024
AD8515
200 VS = 0.9V 4.994
OUTPUT IMPEDANCE ()
4.995 VS = 5V IL = 750A
150 4.993
100
50
03024-026 03024-029
GAIN = 100
GAIN = 10 100k
GAIN = 1
0 1k
10k
1M
10M
VOH (V)
4.992
4.991
4.990 -50
0
50 TEMPERATURE (C)
100
150
FREQUENCY (Hz)
Figure 26. Output Impedance vs. Frequency
80
Figure 29. VOH vs. Temperature
VS = 0.9V VIN = 3.2V VIN
VOLTAGE (1V/DIV)
VS = 5V 77
VOUT
CMRR (dB)
03024-027
74
71
68
03024-030
65 -50
0
50 TEMPERATURE (C)
100
150
TIME (200s/DIV)
Figure 27. No Phase Reversal
11 VS = 5V IL = 750A 9
Figure 30. CMRR vs. Temperature
VOL (mV)
7
5
03024-028
3 -50
0
50 TEMPERATURE (C)
100
150
Figure 28. VOL vs. Temperature
Rev. D | Page 11 of 16
AD8515 THEORY OF OPERATION
The AD8515, offered in space-saving SOT-23 and SC70 packages, is a rail-to-rail input and output operational amplifier that can operate at supply voltages as low as 1.8 V. This product is fabricated using 0.6 micron CMOS to achieve one of the best power consumption-to-speed ratios (that is, bandwidth) in the industry. With a small amount of supply current (less than 400 A), a wide unity gain bandwidth of 4.5 MHz is available for signal processing. The input stage consists of two parallel, complementary, differential pairs of PMOS and NMOS. The AD8515 exhibits no phase reversal because the input signal exceeds the supply by more than 0.6 V. Currents into the input pin must be limited to 5 mA or less by the use of external series resistance(s). The AD8515 has a very robust ESD design and can stand ESD voltages of up to 4000 V. This product solves the speed/power requirements for many applications. The wide bandwidth is also stable even when operated with low supply voltages. Figure 5 shows the relationship between the supply voltage vs. the bandwidth for the AD8515. The AD8515 is ideal for battery-powered instrumentation and handheld devices because it can operate at the end of discharge voltage of most popular batteries. Table 6 lists the nominal and end of discharge voltages of several typical batteries. Table 6. Typical Battery Life Voltage Range
Battery Lead-Acid Lithium NiMH NiCd Carbon-Zinc Nominal Voltage (V) 2 2.6 to 3.6 1.2 1.2 1.5 End of Discharge Voltage (V) 1.8 1.7 to 2.4 1 1 1.1
POWER CONSUMPTION vs. BANDWIDTH
One of the strongest features of the AD8515 is the bandwidth stability over the specified temperature range while consuming small amounts of current. This effect is shown in Figure 2 through Figure 4.
Rev. D | Page 12 of 16
AD8515 DRIVING CAPACITIVE LOADS
Most amplifiers have difficulty driving large capacitive loads. Additionally, higher capacitance at the output can increase the amount of overshoot and ringing in the amplifier's step response and can even affect the stability of the device. This is due to the degradation of phase margin caused by additional phase lag from the capacitive load. The value of capacitive load that an amplifier can drive before oscillation varies with gain, supply voltage, input signal, temperature, and other parameters. Unity gain is the most challenging configuration for driving capacitive loads. The AD8515 is capable of driving large capacitive loads without any external compensation. The graphs in Figure 31 and Figure 32 show the amplifier's capacitive load driving capability when configured in unity gain of +1. The AD8515 is even capable of driving higher capacitive loads in inverting gain of -1, as shown in Figure 33.
VS = 2.5V CL = 50pF GAIN = 1
VOLTAGE (100mV/DIV)
VS = 0.9V CL = 800pF GAIN = -1
VOLTAGE (100mV/DIV)
TIME (1s/DIV)
Figure 33. Capacitive Load Driving @ CL = 800 pF
FULL POWER BANDWIDTH
The slew rate of an amplifier determines the maximum frequency at which it can respond to a large input signal. This frequency (known as full power bandwidth, FPBW) can be calculated from the equation
FPBW = SR 2 x V PEAK
for a given distortion. The FPBW of the AD8515 is shown in Figure 34 to be close to 200 kHz.
03024-031
VIN
VOLTAGE (2V/DIV)
TIME (1s/DIV)
Figure 31. Capacitive Load Driving @ CL = 50 pF
VS = 2.5V CL = 500pF GAIN = 1
VOLTAGE (10mV/DIV)
TIME (2s/DIV)
Figure 34. Full Power Bandwidth
TIME (1s/DIV)
Figure 32. Capacitive Load Driving @ CL = 500 pF
03024-032
Rev. D | Page 13 of 16
03024-034
VOUT
03024-033
AD8515 A MICROPOWER REFERENCE VOLTAGE GENERATOR
Many single-supply circuits are configured with the circuit biased to one-half of the supply voltage. In these cases, a false ground reference can be created by using a voltage divider buffered by an amplifier. Figure 35 shows the schematic for such a circuit. The two 1 M resistors generate the reference voltages while drawing only 0.9 A of current from a 1.8 V supply. A capacitor connected from the inverting terminal to the output of the op amp provides compensation to allow for a bypass capacitor to be connected at the reference output. This bypass capacitor helps establish an ac ground for the reference output.
1.8V TO 5V
fL = fH =
1 2 x R1 x C1 1 2 x R1 x C1
R1 R2
H0 = 1 +
VCC = 1.8 V - 5 V where: fL is the low -3 dB frequency. fH is the high -3 dB frequency. H0 is the midfrequency gain.
VCC VCC
R2 1M C3 1F R1 1M
3 4
+ -
U1 V+ V- 1
R4 100
0.9V TO 2.5V C1 1F
R6 1M V11 400mV
03024-035
AD8515
C2 0.022F R3 10k
R5 2k
3
+
U9 V+ V- 0 R2 20k C6 10pF 1
VOUT
4- C1 2nF R1 5k
AD8515
C3 1F
R8 1M
Figure 35. Micropower Voltage Reference Generator
0
A common-mode bias level is easily created by connecting the noninverting input to a resistor divider consisting of two resistors connected between VCC and ground. This bias point is also decoupled to ground with a 1 F capacitor.
0 1k
10k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 37. Frequency Response of the Band-Pass Filter
Rev. D | Page 14 of 16
03024-037
The circuit in Figure 36 is commonly used in portable applications where low power consumption and wide bandwidth are required. This figure shows a circuit for a single-supply band-pass filter with a center frequency of 100 kHz. It is essential that the op amp have a loop gain at 100 kHz to maintain an accurate center frequency. This loop gain requirement necessitates the choice of an op amp with a high unity gain crossover frequency, such as the AD8515. The 4.5 MHz bandwidth of the AD8515 is sufficient to accurately produce the 100 kHz center frequency, as the response in Figure 37 shows. When the op amp bandwidth is close to the center frequency of the filter, the amplifier internal phase shift causes excess phase shift at 100 kHz, altering the filter response. In fact, if the chosen op amp has a bandwidth close to 100 kHz, the phase shift of the op amps causes the loop to oscillate.
Figure 36. Second-Order Band-Pass Filter
2
OUTPUT VOLTAGE (V)
1.5
1
0.5
03024-036
A 100 kHz SINGLE-SUPPLY SECOND-ORDER BAND-PASS FILTER
AD8515
WIEN BRIDGE OSCILLATOR
The circuit in Figure 38 can be used to generate a sine wave, one of the most fundamental waveforms. Known as a Wien Bridge oscillator, it has the advantage of requiring only one low power amplifier. This is an important consideration, especially for batteryoperated applications where power consumption is a critical issue. To keep the equations simple, the resistor and capacitor values used are kept equal. For the oscillation to happen, two conditions have to be met. First, there should be a zero phase shift from the input to the output, which happens at the oscillation frequency of
fOSC = 1 2 R10 x C10
High frequency oscillators can be built with the AD8515, due to its wide bandwidth. Using the values shown, an oscillation frequency of 130 kHz is created and is shown in Figure 39. If R11 is too low, the oscillation might converge; if too large, the oscillation diverges until the output clips (VS = 2.5 V, fOSC = 130 kHz).
Second, at this frequency, the ratio of VOUT to the voltage at the positive input (+IN, Pin 3) has to be 3, which means that the ratio of R11:R12 should be greater than 2.
C9 1nF R19 1k VCC 3 2 + - U10 V+ V- VEE R12 1k R11 2.05k
03024-038
VOLTAGE (2V/DIV)
Figure 39. Output of Wien Bridge Oscillator
1
C10 1nF
R13 1k
AD8515
Figure 38. Low Power Wien Bridge Oscillator
Rev. D | Page 15 of 16
03024-039
AD8515 OUTLINE DIMENSIONS
2.90 BSC
5 4
1.60 BSC
1 2 3
2.80 BSC
PIN 1 0.95 BSC 1.30 1.15 0.90 1.90 BSC
1.45 MAX
0.22 0.08 10 5 0 0.60 0.45 0.30
0.15 MAX
0.50 0.30
SEATING PLANE
COMPLIANT TO JEDEC STANDARDS MO-178-A A
Figure 40. 5-Lead Small Outline Transistor Package [SOT-23] (RJ-5) Dimensions shown in millimeters
2.20 2.00 1.80 1.35 1.25 1.15 PIN 1 1.00 0.90 0.70
5 1 2 4 3
2.40 2.10 1.80
0.65 BSC 1.10 0.80 0.40 0.10 0.46 0.36 0.26
0.10 MAX
0.30 0.15
SEATING PLANE
0.22 0.08
0.10 COPLANARITY COMPLIANT TO JEDEC STANDARDS MO-203-AA
Figure 41. 5-Lead Thin Shrink Small Outline Transistor Package [SC70] (KS-5) Dimensions shown in millimeters
ORDERING GUIDE
Model AD8515ART-R2 AD8515ART-REEL AD8515ART-REEL7 AD8515ARTZ-R2 1 AD8515ARTZ-REEL1 AD8515ARTZ-REEL71 AD8515AKS-R2 AD8515AKS-REEL AD8515AKS-REEL7 AD8515AKSZ-R21 AD8515AKSZ-REEL1 AD8515AKSZ-REEL71
1
Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C
Package Description 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SC70 5-Lead SC70 5-Lead SC70 5-Lead SC70 5-Lead SC70 5-Lead SC70
Package Option RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 KS-5 KS-5 KS-5 KS-5 KS-5 KS-5
Branding BDA BDA BDA BDA# BDA# BDA# BDA BDA BDA BDA# BDA# BDA#
Z = RoHS Compliant Part; # denotes RoHS product, may be top or bottom marked.
(c)2002-2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03024-0-7/07(D)
Rev. D | Page 16 of 16

▲Up To Search▲

Price & Availability of AD851507

	To Download AD851507 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .